MKII Bullnose RMR Cut Slide for Glock 26 Gen 1–4 – 9mm

Upgrade your Glock 26 with the MKII Bullnose RMR Cut Slide, featuring an aggressive lightweight design, precision-machined optic cut, front and rear serrations, and a ported top profile.

Designed for Glock 26 Gen 1, Gen 2, Gen 3, and Gen 4 frames, this stripped slide is machined from 416 stainless steel and heat treated to 42–44 HRC for strength and durability.

Glock 26 Gen 1–4 Compatibility

This is a Gen 3-pattern slide.

To install it on a Glock 26 Gen 4 frame, you must use Gen 3-compatible slide components. A Gen 3 recoil spring/guide rod is included to assist with Gen 4 installation.

Other Gen 3 slide components are not included.

Compatible with:

• Glock 26 Gen 1

• Glock 26 Gen 2

• Glock 26 Gen 3

• Glock 26 Gen 4

This slide is not compatible with Glock Gen 5 or Gen 6 frames.

Optic Compatibility

The slide is machined for precise fitment of a Trijicon RMR and is also compatible with:

• Trijicon RMR

• Trijicon SRO

• Holosun 407C

• Holosun 507C

• Holosun 508T

• ADE RD3-019 Stingray

• ADE RD3-020 Raptor

• ADE RD3-023 Valkyrie Gen 2

• ADE RD3-031 Helios

• Other red-dot sights using the same RMR footprint

An optic cover plate is included, allowing the slide to be used without a red-dot sight installed.

Lightweight MKII Design

The MKII slide incorporates aggressive machining and weight-reduction cuts while maintaining a durable 416 stainless-steel construction.

Front and rear serrations provide additional gripping surfaces for slide manipulation, while the ported top design gives the slide a distinctive appearance.

The top ports are designed to align with our compatible ported Glock 26 barrel when the two are used together.

Specifications

Model Compatibility: Glock 26 Gen 1–4
Caliber: 9mm Luger
Slide Type: Stripped MKII Bullnose Slide
Pattern: Gen 3
Material: 416 Stainless Steel
Heat Treatment: 42–44 HRC
Weight: Approximately 8.8 oz
Overall Length: Approximately 6.26"
Optic Cut: Trijicon RMR Footprint
Optic Mounting Pattern: 6-32
Sight Cuts: Standard Glock front and rear sight cuts
Finish: H-190 Cerakote
Upper Parts Compatibility: Gen 3-compatible slide components
Gen 3 Recoil Spring / Guide Rod: Included
Optic Cover Plate: Included

Please Note

• This is a stripped slide, not a complete slide assembly.

• A complete Gen 3 slide parts kit is not included.

• The barrel and sights are not included.

• The channel liner is not installed or included.

• Gen 4 installation requires Gen 3-compatible slide components and the included Gen 3 recoil spring/guide rod.

• This slide is not compatible with Glock Gen 5 or Gen 6 frames.

• Professional installation or installation by a qualified gunsmith is recommended.

• Verify proper fit and safe operation before use.

Optic Installation

Use the correct-length screws for your specific optic.

Tighten the optic mounting screws to a maximum of 10–12 in-lb. Applying one small drop of blue threadlocker is recommended.

Cover plate screw size: 6-32 × 7/16 inch.

Because aftermarket frames, barrels, internal components, and optics may have different manufacturing tolerances, minor fitting may occasionally be required.

Important Compatibility Notice

Please verify your firearm model and generation before ordering.

This listing is specifically for a Glock 26 Gen 1–4 compatible slide. Although it can be installed on Gen 4 frames, the slide itself follows the Gen 3 pattern and therefore requires Gen 3-compatible slide components.

It is not compatible with Glock Gen 5 or Gen 6 frames.