- Comes with a ADE RD3-013 red dot, a Picatinny plate and a pistol optic plate to REPLACE the rear sight of G2c, G2s, G2, PT111 G2, Millennium G2, and TX22 Pistols. This plate also fits Taurus G3 with Original Rear sight(see photo)
- Does NOT fit Taurus new TX22C( TX22 Compact) which is Optics Ready, please see ADE RD3-018 SPIKE and RD3-021 NUWA(and NUWA PRO) and RD3-030 Apollo fit directly without any plate/adaptor.
The pistol plate does NOT fit G3 with NEWER FACTORY STEEL SIGHT, G3C, please search ADE G3C plate on amazon under different listing.- 4 MOA. Top load system, no need to remove the sight to change the battery. Red dot has multi brightness level with one adjustment button. Every time you turn on the dot it stays the same brightness level last time it was turned off
- 6 MOA. 1.75" length x1.25" width x1.15" height. Fully windage and elevation adjustable and lockable; Unlimited Eye Relief. Full metal construction with glass lens. No plastic body, no plastic lens.
- Comes with protective cover, screws, wrenches, instructions, lens cloth, anti flickering shim.
- Installing optic plate to handgun is NOT recommended for users that are not familiar with pistol assembly. This optic plate requires removal of the rear sight, dissemble the pistol slide to reach the screw hole underneath. Gunsmith experience is required. We recommend hiring a professional gunsmith. Please note. Unprofessional installation such as improper torque will result in screw loose, not holding zero, damage to the firearm/optic and personal injury.
- Shock proof，Fog proof and Waterproof for 30 minutes under 4ft water
- New advanced battery technology gives up to 3000 hours on bright setting and up to 40k hours on Low setting with a 2032 Battery(Included). Every time you turn on the dot it stays the same brightness level last time it was turned off
- Taurus is a registered trademarks belong to their respective owner. This optic plate for Taurus is made by ADE to connect optics to Taurus pistols. ADE is not affiliated with Taurus.
21 Reviews Hide Reviews Show Reviews
-
Works great
Fits a tx22 (1st generation) perfectly. Easy install. Easy to zero using barrel site laser. After 500 rounds, holding zero . Too bad they don’t make one for 2nd generation.
-
Small and lightweight
This is a great optic for the money, especially if you have a pistol that's sensitive to too much weight on the slide, I'd like it more if it was shake awake but when you put the cover on it the brightness turns really low, I'm interested to see how long the battery will last
-
Awesome Sight!
Large clear dot. The auto brightness feature works perfectly. Zeroed easily and has held Zero through 500 rounds so far. Time will tell on battery longevity. All in all, it is a great sight for a fraction of the price of other sights with the same the features.
-
Fit rmr cut golck slide
Fit my glock 26 slide great. Has held zero so far. Love it.
-
5.0 out of 5 stars No complaints
Holding zero after a couple thousand rounds and continues to function perfectly
-
it still work on the first batter and the thing is always on that's great
I like the green lite
-
May work, cheap enough to give it a try.
I bought the kit to mount this on a Taurus G2 Millennium (PT111) with the "old" style rear sight. The mount plate that was sent with the optic had a small dent in the front edge that is meant to hold the plate in place in the slide. In theory this would be great, however, the metal is soft enough that during installation, this peen dent basically flattens. I pressed forward - I used blue loctite on the super tiny screw that came out of the rear optic to install the mount plate/adapter. The description said a screw was included, but none of the included hardware fit my slide. Mounting the optic was noneventful. I placed the rubber "shock shim" which was included with the sight, and torqued the two fasteners down to 25 inch pounds. Used a laser boresight to get the dot close to center, and headed to the range. Because this slide was not designed to have an optic mounted on it, I found I had to drastically lower the dot, so that POA and POI were matched. I got fairly close. After a dozen or so rounds, I had to reset zero (not good). Four more shots and reset zero.. well this sucks, right? It wasn't the dot drifting, it was the mounting plate loosening. Like, SLOPPY loose. Ok, back home I go, pull it all apart, used a punch to re-peen the mount plate. tried ALL of the hardware again to see if MAYBE i missed the screw that should hold the mount adapter, nope. Applied red loctite and tighten to 25in/lbs.... The plate doesnt work. The recoil was too much for it. I lasted longer with the red loctite, but the recoil began to cycle the power on the optic. Not so I had to turn it back on, but it would shut off, then turn back on - that's odd. This was a fun experiment, but nothing I can run safely. At the end of the day, guns are for safety and if you cant see your target, they're worthless. Caveat - i replaced the slide with a G3 TORO slide (yep, it fits), ditched the mount plate provided with the optic and used the RMR adapter for the slide, and the optic works like a champ. These are fun for plinkers, but sadly, if you choose to run a Taurus CCW, you're gonna need to buy an optic that costs as much as your gun to be safe and reliable. 7 people found this helpful
-
Good quality
Nice sight the mounting plate fit perfect good and tight no wiggling plan to get another one for my other Taurus G2C.
-
Good sight, bad mounting plate
Package included everything necessary to install, including batteries, screwdrivers, allen wrenches, mounts, etc. Easy to change brightness, turn on/off with the button, and install battery. Initial dot position was extremely set to the right, and very high -- adjustment is pretty straight forward. Still need to zero it in at the range. Not sure how durable or waterproof it is but everything seems to work out of the box. The plate is pretty awful. front edge is completely squared, not beveled to fit the slot. Rear edge is beveled, but a bit short; there was a hammer mark that created a bulge that made it too large to slide in all the way. I almost would take off two stars for this, but it's just a mounting plate.
