ADE NUWA RD3-021 Ultra Red Dot Sight For Canik TP9 Elite SC, Canik METE MC9, METE SFT, Sig Sauer P322/P365-380/P365X,Ruger Max-9,Glock 43/48 MOS,Taurus GX4 Toro,856Toro,605Toro,Kimber R7 Mako,Springfield Hellcat OSP,Masada SLIM,SW Equalizer 9M,MP 5.7

(No reviews yet) Write a Review
RD3-021 NUWA
1.00 Ounces
Free Shipping

ADE NUWA is the first(and the only)red dot with RMS/RMSc footprint that has TOP BATTERY LOADING system, no need to Remove the sight to change the Battery that requires re-sight in and waste ammo. Battery life approximately 500-800 depends on the brightness setting.


Designed to fit

Bul Armory SAS II lightweight 3.25 Comp


Canik Elite TP9 SC



Canik METE MC9

Sccy cpx-2

FN Reflex™ MRD

Sig P320 Xten (Using Sig provided plate marked for Leopold Deltapoint Pro optic footprint)

Sig P322

Sig P365-380(make sure your model is exactly called "P365-380", not P360 or P380)


Sig P365 X Macro

Sig P365 California Compliant (Sig released it in late 2023/early 2024)

Ruger Max-9

Glock 43X MOS/48 MOS(not compatible with regular glock 43x/48 that are not MOS)

Springfield Hellcat OSP

Springfield XDS MOD 2 OSP

Springfield Elite 3.8” Compact OSP 9mm 

S&W Shield 2.0 Optics Ready

S&W 9mm Equalizer

S&W M&P9 shield plus Optics Ready


S&W MP 5.7

S&W M&P shield plus performance center

Walther PPS M2 Optics Ready

Kimber Mako7

Girsan MC1911SC Ultimate

Mossberg MC2SC/MC2c

Masada SLIM 

Taurus GX4 Toro

Taurus TX22 Compact

Taurus 865 Toro

Taurus 605 Toro

Rock Island STK-100

Plus any pistol/mounting plate/slide with RMS/RMSC screw pattern/footprint. 


Hard coated aircraft aluminum and multi-coated glass. Not plastic body with polymer lens.


2MOA Red Dot. Weight approximately 15.5 grams(0.55oz), (Length)1.5" x (Width)..88" x (Height).89"


Comes with screws for several Optics Ready handguns. Does not comes with any mounting plate such as picatinny mount or plate made for a specific handgun.


Ade Nuwa created an iron sight curve at the end of the body, and also added two white dots on the curve. For the rear of part of the red dot to become a back up iron sight. With the ultra short design, the red dot provides a distance/gap on some full size optics ready pistols, to give enough distance to be a Co-Witness back up sight, in addition to the LED dot and pistol equipped iron sight


For non-optics ready pistols that need to use an optic plate/adapter to replace the pistol manufacturer equipped rear sight, ADE NUWA's rear white dot will act as a pistol factory original rear sight for Co-Witness.


ADE Nuwa is manual activated by pressing the on/off switch. Press and Hold switch for 2 seconds to turn on/off, quick press to adjust the brightness from low to high.


For non-optics ready pistols that need to use an optic plate/adapter to replace the pistol manufacturer equipped rear sight, ADE NUWA's rear white dot will act as a pistol factory original rear sight for Co-Witness.



Comes with 3 pairs of screws for Sig P365XL/X, Springfield Hellcat OSP and Canik TP9 Elite SC ONLY. The provided screws might NOT work with EVERY compatible pistol listed. ADE makes the red dot to accept the industrial standard footprint. The pistol manufacturer makes the optic cut/slide for the same footprint, but they have their own opinions to decide which type screws that the screw holes take.


ADE Does not know the screw spec every pistol manufacture used for their screw hole. Please ask the pistol manufacture what screw specs they used on the hole and ask them to provide the screw. If you can’t get the screw to work properly, we recommend going to a local hardware store such as ACE Hardware to get the right size.




ADE RD3-006B, RD3-009, RD3-012, RD3-013 and RD3-028 fit optic cut/plate that is compatible with Vortex Venom/Burris Fastfire/Doctor footprint


ADE RD3-018 Spike, RD3-021 Nuwa and RD3-030 Apollo fit optic cut/optic plate that is compatible with shield RMS/RMSC/Deltapoint Pro footprint


ADE RD3-019 Stingray RD3-020 Raptor, RD3-023 Valkyrie and RD3-029 Trumpet fit optic cut/optic plate/ that is compatible with Trijicon RMR/SRO/Holosun 407C/507C footprint



Ade Advanced Optics first made its appearance in the firearms accessory industry by doing private label production for several Major manufacturers and retailers. During this period, Ade Advanced Optics began receiving requests from numerous customers for access to the affordable, high quality products that Ade Advanced Optics was capable of producing. By soliciting feedback from both clients and end users in 2010, Ade Advanced Optics was able to overcome the challenges a new company often faces when entering a global market and industry, especially one as competitive as the shooting, hunting, and outdoors industry.

Related Products